Bitustik 1000

BITUSTICK 1000 is a 1mm thick preformed self adhesive modified bituminous membrane specifically designed for waterproofing and damp proofing of below ground concrete structures where the ground water table is low.  BITUSTICK 1000 conforms to the requirements of BS 8102. More..


POLYSEAL PS PG

POLYSEAL PS PG is a two component pourable, self leveling polysulphide resin based joint sealant. POLYSEAL PS PG is specifically designed to be used as a watertight seal for moderate movement and control joints in horizontal areas. It is based on a liquid polysulphide polymer which when mixed with the hardener, cures to form a tough, flexible and non staining rubber like seal. POLYSEAL PS PG has excellent adhesion to concrete, stone, metals and other common building surfaces. The cured sealant has good resistance to most environmental chemicals & resists deterioration on prolonged exposure to UV. POLYSEAL PS PG is suitable for use in horizontal areas with a maximum slope gradient of 10%. The sealant has a Movement Accomodation Factor (MAF) of ±25%.More..


POLYPRIME PS

POLYPRIME PS is a single component solvent based adhesion promoting primer for movement and control joints in porous substrates like concrete, block work, asbestos and timber. The primer forms a chemical bridge between the concrete surface and the sealant which is applied into the joint.More..


Polycoat RBE

Polycoat RBE is an emulsified rubber modified bitumen coating, which dries to form a tough, seamless, flexible vapor proof protective coating. More..


Polyflex TDS

Polyflex is a two part acrylic modified cementitious coating for protecting concrete structures against water, vapor, ingress of chloride ions, attacks of acidic gases and alkalis. It cures to form a tough flexible coating having excellent waterproofing properties. Polyflex is a blend of cement, selected fillers, polymers and graded silica sand which is in the powder form. The liquid contains acrylic co-polymers and wetting agents. More..


Polyprime SB

Polyprime SB is a quick drying solvent based low viscosity bitumen primer. It is used as a primer coat on masonry and concrete substrates to improve the adhesion of bitumen based membranes and coatings. Polyprime SB is low in viscosity, which allows it to penetrate into the concrete pores and improve the adhesion between the membrane and the concrete surface. In addition to that, the primer also acts as a binder for the dust particles which gets accumulated on the concrete surface even after cleaning. More..


POLYBOND SBR

POLYBOND SBR is a Styrene Butadiene Rubber copolymer based product which is used in mortar and
concrete as an admixture and bonding agent to increase its water resistance and durability.More..


POLYCRETE FC

POLYCRETE FC is a single component polymer modified fairing coat designed to fill pores, blowholes,
minor honeycombs on a concrete surface. This can also be used as a skim coat prior to the application
of protective coatings. It is a shrinkage compensated crack free material, which can be applied as thin
surface coats.More..


POLYCRETE ST

POLYCRETE ST is a high strength structural polymer modified repair mortar. The product is specially
formulated by blending OPC with non shrinking additives, fibres, polymers and fillers for repairing of
beams, columns and Slabs in structures which are subjected to dynamic loads and traffic.More..


POLYCURE AC

POLYCURE AC is a non-degradable liquid type of curing and sealing compound based on acrylic and
proper wetting agents. POLYCURE AC is used to prevent rapid evaporation of water from fresh concrete
ensuring uniform hydration, adequate strength development and minimizes plastic and drying shrinkage
cracks. This will also act as sealing coat for protecting concrete from the attack of water borne salts and
ingress of carbon dioxide from the atmosphere. The cured film further acts as a primer system for
subsequent surface finishes. It also provides a dust free surface to the concrete with a reduced incidence
of drying shrinkage cracks.More..


POLYGROUT NS

POLYGROUT NS is a cementitious non shrink grout which when mixed with water gives a free flowing
shrinkage compensated grout of excellent workability and performance. POLYGROUT NS is a blend of
selected cement, graded fillers and chemical additives. These special additives imparts controlled
expansion in plastic state at the same time minimize water requirement. This low water demand ensures
high early strength and controlled expansion compensates the initial shrinkage.More..


POLYPOXY BF

POLYPOXY BF is a two component solvent free, epoxy resin based repair putty and mortar for concrete
surfaces. The epoxy putty consists of graded fillers and non sagging agents which makes its ideal for
application on vertical surfaces.
POLYPOXY BF is designed for filling of blow holes, cracks and minor imperfections on concrete surfaces.More..


POLYRELEASE

POLYRELEASE is a chemical release agent applied on mould and shutter surfaces prior to casting concrete.
It ensures a smooth and uniform finish to the concrete.More..


POLYSEAL 1PU

POLYSEAL 1PU is a one part low modulus high performance polyurethane sealant, which cures on absorption
of atmospheric moisture to form a firm and flexible rubber watertight seal for moderate movement
and control joints. POLYSEAL 1PU can be used in both horizontal and vertical applications. The sealant
has a Movement Accomodation Factor (MAF) of ±25%.More..


POLYTAPE AL

Polytape AL flash band is a self-adhesive, aluminum surfaced bitumen backed sealing strip. It is quick,
efficient and cost effective method of flashing, sealing and repair that produces a lasting protection in all
climates.More..



POLYHARD

POLYHARD is a ready to use factory blended cementitious powder, which has been formulated to provide hard wearing surface when applied as a dry shake powder over freshly floated concrete surface. POLYHARD contains specially selected aggregates with excellent abrasion and wear resistance along with cementitious binders, plasticizers and admixtures to provide a tough & durable floor. More..


POLYHARD L

POLYHARD L is a colorless low viscous liquid applied to floors to get a hard and dustproof finish. The ingredients present in Polyhard L react with the free lime present in cement and on hydration form hard and insoluble crystals, thus binding the particles and providing the floor with a hard and dust free surface. More..


POLYPRIME PU

POLYPRIME PU is a two component solvent free epoxy resin based primer and sealer coat for polyurethane based coatings and toppings. POLYPRIME PU can also be applied as a scratch coat with the addition of graded quartz sand. More..


POLYPUR TC 20

POLYPUR TC 20 is a two component high quality UV stable polyurethane car park deck coating system. The coating provides a seamless, abrasion resistant floor coating system for both internal and external areas. More..


POLYPUR WC 40

POLYPUR WC 40 is a multi component high quality elastomeric intermediate polyurethane resin based wearing coat for car park deck coating system. POLYPUR WC 40 is designed to provide a flexible and crack bridging waterproofing coating for highly trafficked areas. More..